Code Alarm SRT 6700 Service Manual download pdf (Page 17)

Auxiliary Output Parameters List • 11

9 Parameters List

REGULATION

rtC Access to CLOCK submenu (if present)

EEU Access to EEV submenu (only XM679K);

Differential: (0.1 to 25.5°C; 1 to 45°F) This is the intervention differential for setpoint, this value is always

positive. Solenoid valve Cut IN is Setpoint Plus Differential (Hy). Solenoid valve Cut OUT is when the

temperature reaches the setpoint.

Int

Integral time for room temperature regulation (Only XM679K): (0 to 255 s) This is the integral time for room

temperature PI regulator. 0= no integral action.

CrE

Continuous regulation activation (Only XM679K): (n to Y) n= standard regulation; Y= continuous

regulation. Use it only in centralized plants;

LS Minimum setpoint limit: (-55.0°C to SET; -67°F to SET) Sets the minimum acceptable value for the setpoint.

US Maximum setpoint limit: (SET to 150°C; SET to 302°F) Set the maximum acceptable value for setpoint.

OdS

Outputs activation delay at start up: (0 to 255 min) This function is enabled at the initial start up of the device

and inhibits any output activation for the time set in the parameter. (AUX and Light can work)

AC Anti-short cycle delay: (0 to 60 min) The interval between the solenoid valve stop and the following restart.

CCt

Compressor ON time during continuous cycle: (0.0 to 24.0h; resolution 10min) Allows to set the length of

the continuous cycle: compressor stays on without interruption for the CCt time. Can be used, for instance,

when the room is filled with new products.

CCS

Setpoint for continuous cycle: (-55 to 150°C / -67 to 302°F) it sets the setpoint used during the continuous

cycle.

Con

Solenoid valve ON time with faulty probe: (0 to 255 min) The time during which the solenoid valve is active

in case of faulty thermostat probe. With COn=0 solenoid valve is always OFF.

CoF

Solenoid valve OFF time with faulty probe: (0 to 255 min) time during which the solenoid valve is off in case

of faulty thermostat probe. With COF=0 solenoid valve is always active

DISPLAY

Temperature measurement unit: °C = Celsius; °F = Fahrenheit. CAUTION! When the measurement unit is

changed the parameters with temperature values have to be checked.

PrU

Pressure mode: (rEL or AbS) it defines the mode to use the pressure. CAUTION! the setting of PrU is used

for all the pressure parameters. If PrU = rEL all pressure parameters are in relative pressure unit, if PrU =

AbS all pressure parameters are in absolute pressure unit. (Only XM679K)

PMU

Pressure measurement unit: (bAr - PSI - MPA) it selects the pressure measurement units. MPA= the value of

pressure measured by kPA*10. (Only XM679K)

PMd

Way of displaying pressure: (tEM - PrE) it permits showing the value measured by pressure probe with tEM=

temperature or by PrE= pressure; (Only XM679K)

rES Resolution (for °C): (in = 1°C; dE = 0.1 °C) allows decimal point display;

Lod

device display: (nP; P1; P2, P3, P4, P5, P6, tEr, dEF) it selects which probe is displayed by the device. P1,

P2, P3, P4, P5, P6, tEr= virtual probe for thermostat, dEF= virtual probe for defrost.

Table 9-1 - XM670K to XM679K Parameters List

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 53 54

Comments to this Manuals

No comments

Code Alarm SRT 6700 Service Manual Page 17

Comments to this Manuals

Related products and manuals for Car alarm Code Alarm SRT 6700