Code Alarm F60 Installation Manual Page 151
- Page / 181
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Diagnostics and troubleshooting
S1A53838 09/2011 151
Err2
[RAM fault]
• The control board RAM is inoperable. • Contact Schneider Electric to repair the
drive.
Err3
[ROM fault]
• The control board ROM is inoperable. • Contact Schneider Electric to repair the
drive.
Err4
[CPU fault 1]
• The control board CPU is inoperable. • Contact Schneider Electric to repair the
drive.
Err5
[Com RJ45 fault]
• Serial communication error • Check network control devices and cables.
• Check the setting of the communication
timeout parameter, F803.
• Check the remote graphic display option
cable.
• Check the setting of F829 parameters.
Err7
[Current sensor fault]
• A motor current sensor is inoperable. • Replace the drive.
Err8
[Network error fault]
• Network communication error • Check the network control devices and
cables.
Err9
[Remote keypad
fault]
• Graphic display option cable disconnected • Check the RJ45 cable.
Etn1
[Auto-tuning fault]
• Parameters F401 to F494 are
incorrectly set.
• The motor is too large for the drive.
• The motor cable gauge is too small.
• The motor is still rotating at the start of the
auto-tune.
• The drive is not powering a 3-phase
induction motor.
• Set parameters F401–F494 correctly.
• Use a larger drive.
• Use a larger gauge motor cable.
• Verify that the motor is stopped before
starting an auto-tune.
• Use the drive to power only a 3-phase
induction motor.
EtYP
[Drive fault]
• The main control board is inoperable. • Set parameter [Parameter reset] (tYP) to
6.
• If this does not clear the detected error,
replace the drive.
Fd1
[Closed damper 1
fault]
• Damper is locked in closed position. • Set [Damper flt behavior] (F583) to 0.
• Check the FL relay connection (FLA/FLB).
• Check the relay configuration
(
F130/F132).
Fd2
[Closed damper 2
fault]
• Damper blocked open or soldered. • Set [Damper fdb type] (F580) to 0 or
1.Check the FL relay connection
(
FLA/FLB).
• Check the relay configuration
(
F130/F132).
M020
[Total input power]
• The accumulated input power value is more
than 999.999 kWh.
• Clear the accumulated input power value
using logic input function 51, or parameter
F748.
OC1
[Overcurrent
acceleration]
• The acceleration time is too short.
• The setting of parameter [Mot cont. mode
sel.] (Pt) is incorrect.
• The drive is starting into a rotating load.
• The drive is powering a low impedance
motor.
• Ground fault
• Increase the acceleration time parameters
(ACC or F500).
• Select the correct setting for parameter [Mot
cont. mode sel.] (Pt).
• Enable catch on the fly, parameter F301.
• Adjust the switching frequency parameter
F300.
• Set parameter F316 to 1 or 3.
OC1P
[SC or ground fault
acc.]
• Short circuit or ground fault during
acceleration
• Using a 1000 V testing tool megger, check
the motor and motor cables for ground faults.
OC2
[Overcurrent
deceleration]
• The deceleration time is too short.
• Ground fault
• Increase the deceleration time parameters
(dEC or F501).
• Set parameter F316 to 1 or 3.
OC2P
[SC or ground fault
dec.]
• Short circuit or ground fault during
deceleration
• Using a 1000 V megger, check the motor and
motor cables for ground faults.
OC3
[Overcurrent cont.
speed]
• Abrupt fluctuations in load
• Abnormal load condition
• Reduce the load fluctuations.
• Check the load.
• Set parameter F316 to 1 or 3.
OC3P
[SC/ground flt cont.
spd]
• Short circuit or ground fault during constant
speed operation
• Using a 1000 V megger, check the motor and
motor cables for ground faults.
OCA
[SC inverter at start]
• Ground fault • Using a 1000 V megger, check the motor and
motor cables for ground faults.
OCL
[SC mot. cable at
start]
• Phase to phase output short circuit
• The motor impedance is too low.
• Using a 1000 V megger, check the motor and
motor cables for ground faults.
Code Name Possible causes Remedies
- Altivar 212 1
- 2 S1A53838 09/2011 2
- Table of Contents 3
- 4 S1A53838 09/2011 4
- S1A53838 09/2011 5 5
- 6 S1A53838 09/2011 6
- Safety Information 7
- S1A53838 09/2011 9 9
- About the Book 10
- 10 S1A53838 09/2011 10
- General Overview 11
- 12 S1A53838 09/2011 12
- PROGRAMMING 14
- INSTALLATION 14
- Overview 15
- 16 S1A53838 09/2011 16
- Preliminary recommendations 17
- Embedded display terminal 18
- S1A53838 09/2011 19 19
- Monitoring Mode 20
- Run Mode 23
- Programming Mode 23
- Menu Navigation 24
- Programming 25
- [Quick menu] 25
- 26 S1A53838 09/2011 26
- F--- [EXTENDED MENU] submenu 27
- IO [I/O MENU] submenu 28
- Submenus 30
- Graphic display option 31
- • Press (ENT): 31
- • Turn +/-: 31
- Detected fault screens 33
- Pre-alarms screens 34
- Modbus communication status 34
- PCSoft software workshop 35
- Run forward 38
- Run reverse 38
- RUN STOP 39
- 2.2 to 10 kOhms 40
- 1/4 Watt 40
- 4-20 mAcurrent signal 41
- Feedback 44
- Feedback mA or voltage signal 44
- Setpoint 0 - 10 V 44
- Drive Operation 45
- S1A53838 09/2011 47 47
- 48 S1A53838 09/2011 48
- (F735) 51
- 52 S1A53838 09/2011 52
- 54 S1A53838 09/2011 54
- Quick Menu 55
- AU1 [Auto ramp] 56
- [Acceleration time 1] 56
- LL [Low limit frequency] 56
- UL [Upper limit freq] 56
- Pt [Mot cont. mode sel.] 57
- F417 [Motor rated speed] 59
- F601 [Motor Current Limit] 59
- 60 S1A53838 09/2011 60
- Programming Parameters 61
- Parameter Reset 62
- AU4 [Auto set function] 63
- F700 [Parameter lock] 64
- F738 [Quick menu AUF] 64
- Motor Control Parameters 65
- Motor Control Mode 66
- [Mot cont. mode sel.] (Pt) 68
- Motor Tuning 70
- F400 [Auto-tuning drive] 71
- Expert parameters 72
- F307 [Mot volt limitation] 73
- Motor 2 Control Parameters 74
- F418 [Frequency loop gain] 75
- F419 [Freq. loop stability] 75
- 76 S1A53838 09/2011 76
- Drive Control Parameters 77
- F721 [Loc. mot stop mode] 78
- F295 [Switch rem/Local] 78
- F256 [Time limit low spd] 78
- F207 [Remote spd ref 2] 78
- F650 [Forced fire control] 79
- F659 [Forced fire function] 79
- F294 [Forced speed freq.] 79
- F730 [Up/down key ref] 80
- F732 [Loc/rem key] 80
- F733 [Run/stop key] 80
- F734 [Priority stop] 80
- F735 [HMI reset button] 80
- Application Parameters 81
- Application parameters 82
- (1) (2) (3) (4) 83
- Skip Frequencies 87
- F250 [DC brake start freq.] 88
- F251 [DC braking current] 88
- F252 [DC braking time] 88
- F111 [LI F selection] 90
- F112 [LI R selection] 90
- F113 [LI RES selection] 90
- F109 [VIA selection] 90
- F118 [VIA LI selection] 90
- Inversion of commanded speed 98
- ≠ VIB signal 103
- Analog Input Functions 104
- Analog Output Functions 105
- Analog Input Adjustments 106
- F472 [VIB bias] 107
- F473 [VIB gain] 107
- F470 [VIA bias] 107
- F471 [VIA gain] 107
- F200 [Auto/man speed ref] 108
- [AO funct. selection] 108
- FM [AO scaling] 108
- F147 [FL Relay delay] 110
- F360 [PID control enable] 110
- F362 [PID Prop Gain] 110
- F363 [PID Integral Gain] 110
- Active Logic Function 112
- Preset Speeds 112
- Ω 3000 Ω 112
- +/- Speed Control Parameters 113
- F100 [Freq. 1 reached] 114
- F101 [Freq. 2 reached] 114
- F102 [Freq.2 bandw.] 114
- F167 [Freq band det range] 115
- F603 [Ext. fault stop Mode] 115
- F604 [DC brk time ext flt] 115
- Damper control 116
- F580 [Damper fdb type] 117
- F581 [Time open Damper] 117
- F582 [Time close Damper] 117
- F583 [Damper flt behavior] 117
- I/O Control Parameters 118
- 118 S1A53838 09/2011 118
- Display Parameters 119
- F710 [Displayed param.] 120
- F701 [Unit value selection] 120
- F708 [Display ref. resol.] 120
- F621 [Run time alarm] 120
- F748 [Power cons. memo] 120
- 122 S1A53838 09/2011 122
- What's in this Chapter? 123
- F303 [Number auto reset] 124
- Time delay 125
- F301 [Catch on fly] 126
- F632 [Mot overload memo] 126
- F602 [Drive fault memory] 127
- F608 [Input phase loss] 127
- F302 [Supply loss behav.] 127
- F627 [Undervolt detect.] 127
- F305 [Overvoltage fault] 128
- F626 [Overvoltage level] 128
- F605 [Output phase loss] 129
- F610 [Underload det.] 130
- F611 [Underload level] 130
- F609 [Underload band] 130
- F612 [Underload det. time] 130
- F633 [Loss of VIA] 130
- 0.0 to [Max frequency] (FH) 131
- F615 [Overtorque det.] 132
- F616 [Overtorque level] 132
- F618 [OvTorque det time] 132
- F619 [Overtorque band] 132
- F634 [Amb. temp. alarm] 133
- F481 [In noise comp. filter] 133
- F483 [In noise inhibit gain] 133
- F484 [Pwr supply adj. gain] 133
- Output Frequency (Hz) 134
- - and the protection 135
- 136 S1A53838 09/2011 136
- F800 [Mdb RJ45 baud] 138
- F801 [Mdb RJ45 parity] 138
- F802 [Modbus address] 138
- F856 [Mot. poles (comm.)] 140
- F870 [Block write data 1] 140
- F871 [Block write data 2] 140
- F875 [Block read data 1] 140
- F876 [Block read data 2] 140
- F877 [Block read data 3] 141
- F878 [Block read data 4] 141
- F879 [Block read data 5] 141
- F880 [Free ID parameter] 141
- Speed Reference 144
- Droop Control 145
- Output frequency (Hz) 146
- Command frequency: f 146
- Power running 146
- Torque current (%) 146
- Operation frequency: f 146
- What's in this Part? 147
- 148 S1A53838 09/2011 148
- Detected fault conditions 150
- Alarm Conditions 153
- Pre-alarm Conditions 154
- Clearing the detected fault 155
- 156 S1A53838 09/2011 156
- 158 S1A53838 09/2011 158
- Migration 159
- Migration ATV21 - ATV212 160
- Parameters Reset Tables 161
- 162 S1A53838 09/2011 162
- S1A53838 09/2011 163 163
- 164 S1A53838 09/2011 164
- [Display ref. resol.] 164
- S1A53838 09/2011 165 165
- (1) See table page 167 165
- 170 S1A53838 09/2011 170
- User Settings Tables 171
Related products and manuals for Remote starters Code Alarm F60
Remote starters Code Alarm F60 User's Guide
(107 pages)
(107 pages)
(8 pages)
Remote starters Code Alarm F65 User Manual
(19 pages)
(19 pages)
© 2020, manymanuals.com. All rights reserved. | 3.013 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals