Code Alarm F60 Installation Manual Page 84
- Page / 181
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Application Parameters
84 S1A53838 09/2011
F502
[Acc/dec 1 pattern]
0
0
1
2
[Linear]
[S-ramp 1] (see diagram below)
[S-ramp 2] (see diagram below for [Acc/dec 2 pattern] (F503) parameter).
The linear acceleration and deceleration pattern is illustrated in diagram on page 83
and is used in most applications.
S-pattern 1 (see diagram below) is for use in applications that need the shortest ramp time possible while minimizing jerks during
speed changes. See below for more information about parameters [Acc/Dec S-pat start] (F506) and [Acc/Dec S-pat end]
(F507).
F503
[Acc/dec 2 pattern]
0
0
1
2
[Linear]
[S-ramp 1] See diagram below.
[S-ramp 2] See previous diagram for parameter Acc/Dec Pattern 1 [Acc/dec 1 pattern] (F502).
S-pattern 2 (diagram below) is for use in high-speed spindle applications where acceleration and deceleration rates need to be
reduced as the motor operates above its rated operating frequency—a constant hp region where motor torque is reduced.
Use parameter F503 to select the second Acc/Dec pattern. Switching between Acc/Dec patterns 1 and 2 is accomplished by
means of:
Parameter [Ramp switching]
(F504) (see page 85),
A particular operating frequency (see parameter [Commut. ramp freq.]
(F505) on page 85), or
A logic input assigned to functions 5, 20, 21, 30, 31 – 35, or 40 (see table beginning on page 91
).
For more information on Acc/Dec patterns, see parameter [Acc/dec 1 pattern] (F502) above.
F506
[Acc/Dec S-pat start]
Acc/Dec S-pattern lower limit
0 to 50% of acceleration time 10%
Use parameter F506 to adjust the lower portion of S-pattern 1. See diagram on page 85.
F507
[Acc/Dec S-pat end]
Acc/Dec S-pattern Upper Limit
0 to 50% of acceleration time 10%
Use parameter F507 to adjust the upper portion of the S-pattern 1. See diagram on page 85.
Code Name / Description Adjustment range Factory setting
0
x
x
Output Frequency (Hz)
Maximum Frequency
Actual Acceleration Time
Time (S)
Set Frequency
0
Output Frequency (Hz)
Maximum Frequency
Actual Acceleration Time
Time (S)
Set Frequency
Motor Rated
Frequency
Constant hp
Region
- Altivar 212 1
- 2 S1A53838 09/2011 2
- Table of Contents 3
- 4 S1A53838 09/2011 4
- S1A53838 09/2011 5 5
- 6 S1A53838 09/2011 6
- Safety Information 7
- S1A53838 09/2011 9 9
- About the Book 10
- 10 S1A53838 09/2011 10
- General Overview 11
- 12 S1A53838 09/2011 12
- PROGRAMMING 14
- INSTALLATION 14
- Overview 15
- 16 S1A53838 09/2011 16
- Preliminary recommendations 17
- Embedded display terminal 18
- S1A53838 09/2011 19 19
- Monitoring Mode 20
- Run Mode 23
- Programming Mode 23
- Menu Navigation 24
- Programming 25
- [Quick menu] 25
- 26 S1A53838 09/2011 26
- F--- [EXTENDED MENU] submenu 27
- IO [I/O MENU] submenu 28
- Submenus 30
- Graphic display option 31
- • Press (ENT): 31
- • Turn +/-: 31
- Detected fault screens 33
- Pre-alarms screens 34
- Modbus communication status 34
- PCSoft software workshop 35
- Run forward 38
- Run reverse 38
- RUN STOP 39
- 2.2 to 10 kOhms 40
- 1/4 Watt 40
- 4-20 mAcurrent signal 41
- Feedback 44
- Feedback mA or voltage signal 44
- Setpoint 0 - 10 V 44
- Drive Operation 45
- S1A53838 09/2011 47 47
- 48 S1A53838 09/2011 48
- (F735) 51
- 52 S1A53838 09/2011 52
- 54 S1A53838 09/2011 54
- Quick Menu 55
- AU1 [Auto ramp] 56
- [Acceleration time 1] 56
- LL [Low limit frequency] 56
- UL [Upper limit freq] 56
- Pt [Mot cont. mode sel.] 57
- F417 [Motor rated speed] 59
- F601 [Motor Current Limit] 59
- 60 S1A53838 09/2011 60
- Programming Parameters 61
- Parameter Reset 62
- AU4 [Auto set function] 63
- F700 [Parameter lock] 64
- F738 [Quick menu AUF] 64
- Motor Control Parameters 65
- Motor Control Mode 66
- [Mot cont. mode sel.] (Pt) 68
- Motor Tuning 70
- F400 [Auto-tuning drive] 71
- Expert parameters 72
- F307 [Mot volt limitation] 73
- Motor 2 Control Parameters 74
- F418 [Frequency loop gain] 75
- F419 [Freq. loop stability] 75
- 76 S1A53838 09/2011 76
- Drive Control Parameters 77
- F721 [Loc. mot stop mode] 78
- F295 [Switch rem/Local] 78
- F256 [Time limit low spd] 78
- F207 [Remote spd ref 2] 78
- F650 [Forced fire control] 79
- F659 [Forced fire function] 79
- F294 [Forced speed freq.] 79
- F730 [Up/down key ref] 80
- F732 [Loc/rem key] 80
- F733 [Run/stop key] 80
- F734 [Priority stop] 80
- F735 [HMI reset button] 80
- Application Parameters 81
- Application parameters 82
- (1) (2) (3) (4) 83
- Skip Frequencies 87
- F250 [DC brake start freq.] 88
- F251 [DC braking current] 88
- F252 [DC braking time] 88
- F111 [LI F selection] 90
- F112 [LI R selection] 90
- F113 [LI RES selection] 90
- F109 [VIA selection] 90
- F118 [VIA LI selection] 90
- Inversion of commanded speed 98
- ≠ VIB signal 103
- Analog Input Functions 104
- Analog Output Functions 105
- Analog Input Adjustments 106
- F472 [VIB bias] 107
- F473 [VIB gain] 107
- F470 [VIA bias] 107
- F471 [VIA gain] 107
- F200 [Auto/man speed ref] 108
- [AO funct. selection] 108
- FM [AO scaling] 108
- F147 [FL Relay delay] 110
- F360 [PID control enable] 110
- F362 [PID Prop Gain] 110
- F363 [PID Integral Gain] 110
- Active Logic Function 112
- Preset Speeds 112
- Ω 3000 Ω 112
- +/- Speed Control Parameters 113
- F100 [Freq. 1 reached] 114
- F101 [Freq. 2 reached] 114
- F102 [Freq.2 bandw.] 114
- F167 [Freq band det range] 115
- F603 [Ext. fault stop Mode] 115
- F604 [DC brk time ext flt] 115
- Damper control 116
- F580 [Damper fdb type] 117
- F581 [Time open Damper] 117
- F582 [Time close Damper] 117
- F583 [Damper flt behavior] 117
- I/O Control Parameters 118
- 118 S1A53838 09/2011 118
- Display Parameters 119
- F710 [Displayed param.] 120
- F701 [Unit value selection] 120
- F708 [Display ref. resol.] 120
- F621 [Run time alarm] 120
- F748 [Power cons. memo] 120
- 122 S1A53838 09/2011 122
- What's in this Chapter? 123
- F303 [Number auto reset] 124
- Time delay 125
- F301 [Catch on fly] 126
- F632 [Mot overload memo] 126
- F602 [Drive fault memory] 127
- F608 [Input phase loss] 127
- F302 [Supply loss behav.] 127
- F627 [Undervolt detect.] 127
- F305 [Overvoltage fault] 128
- F626 [Overvoltage level] 128
- F605 [Output phase loss] 129
- F610 [Underload det.] 130
- F611 [Underload level] 130
- F609 [Underload band] 130
- F612 [Underload det. time] 130
- F633 [Loss of VIA] 130
- 0.0 to [Max frequency] (FH) 131
- F615 [Overtorque det.] 132
- F616 [Overtorque level] 132
- F618 [OvTorque det time] 132
- F619 [Overtorque band] 132
- F634 [Amb. temp. alarm] 133
- F481 [In noise comp. filter] 133
- F483 [In noise inhibit gain] 133
- F484 [Pwr supply adj. gain] 133
- Output Frequency (Hz) 134
- - and the protection 135
- 136 S1A53838 09/2011 136
- F800 [Mdb RJ45 baud] 138
- F801 [Mdb RJ45 parity] 138
- F802 [Modbus address] 138
- F856 [Mot. poles (comm.)] 140
- F870 [Block write data 1] 140
- F871 [Block write data 2] 140
- F875 [Block read data 1] 140
- F876 [Block read data 2] 140
- F877 [Block read data 3] 141
- F878 [Block read data 4] 141
- F879 [Block read data 5] 141
- F880 [Free ID parameter] 141
- Speed Reference 144
- Droop Control 145
- Output frequency (Hz) 146
- Command frequency: f 146
- Power running 146
- Torque current (%) 146
- Operation frequency: f 146
- What's in this Part? 147
- 148 S1A53838 09/2011 148
- Detected fault conditions 150
- Alarm Conditions 153
- Pre-alarm Conditions 154
- Clearing the detected fault 155
- 156 S1A53838 09/2011 156
- 158 S1A53838 09/2011 158
- Migration 159
- Migration ATV21 - ATV212 160
- Parameters Reset Tables 161
- 162 S1A53838 09/2011 162
- S1A53838 09/2011 163 163
- 164 S1A53838 09/2011 164
- [Display ref. resol.] 164
- S1A53838 09/2011 165 165
- (1) See table page 167 165
- 170 S1A53838 09/2011 170
- User Settings Tables 171
Related products and manuals for Remote starters Code Alarm F60
Remote starters Code Alarm F60 User's Guide
(107 pages)
(107 pages)
(8 pages)
Remote starters Code Alarm F65 User Manual
(19 pages)
(19 pages)
© 2020, manymanuals.com. All rights reserved. | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals