Code Alarm F60 Installation Manual Page 102
- Page / 181
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
I/O Control Parameters
102 S1A53838 09/2011
36 [Fault relay]
(The drive is not in a fault state during
auto clear detected fault attempts.
See also function 10 page 98
)
WARNING
LOSS OF CONTROL
z When F130, F132, F137 is set to 36, the output will be active
when the drive will detect a fault.
z The drive status will not be detected if the wiring is damaged for any
reason.
z Do not select 36 unless you are sure that your signal will be present
in any case.
Failure to follow these instructions can result in death, serious inju-
ry, or equipment damage.
OFF: No drive detected fault
ON: drive detected
fault.
Relay activates when a clearable fault occurs and the drive attempts to re-
start. Relay deactivates when drive is restarting.
37 [Inv fault relay]
Inversion of Fault relay function 36
OFF: drive detected
fault
ON: No drive detected fault
Relay deactivates when a clearable fault occurs and the drive attempts to
restart. Relay activates when drive is restarting.
38 [Ser. data relay FL]
Serial communication data
OFF: Serial communication word FA50 bit 0 = 0
ON: Serial communication word FA50 bit 0 = 1
39 [Inv ser. dat rel. FL]
Inversion of ser. dat rel. FL function
OFF: Serial communication word FA50 bit 0 = 1
ON: Serial communication word FA50 bit 0 = 0
40 [Ser. data relay RY]
Serial communication data
OFF: Serial communication word FA50 bit 1 = 0
ON: Serial communication word FA50 bit 1 = 1
41 [Inv ser. dat rel RY]
Inversion of ser. dat rel. RY function
OFF: Serial communication word FA50 bit 1 = 1
ON: Serial communication word FA50 bit 1 = 0
42 [Drive run time al]
Drive operational run time alarm
(see page 120
for more detail on
parameter F621).
OFF: Run time is < F621 time setting
ON: Run time is F621 time setting
43 [Inv.drive run time al] Inversion of Drive
run time al function
OFF: Run time is F621 time setting
ON: Run time is < F621 time setting
44
[D
rive serv. alarm]
Drive service alarm (see page 133
for more detail on parameter
F634).
OFF: drive maintenance detected fault not active
ON: drive maintenance detected fault active
45
[Inv. d
rive serv. alarm] Inversion of
Drive serv. alarm function
OFF: drive maintenance detected fault active
ON: drive maintenance detected fault not active
48 [LI F state]
Logic input F state
OFF: Logic input F is not active
ON: Logic input F is active
49
[Inv. LI F state
] Inversion of LI F state
function
OFF: Logic input F is active
ON: Logic input F is not active
50 [LI R state]
Logic input R state
OFF: Logic input R is not active
ON: Logic input R is active
51
[Inv. LI R state
] Inversion of LI R state
function
OFF: Logic input R is active
ON: Logic input R is not active
52 [Speed ref = VIA]
Drive speed reference equals VIA sig-
nal
OFF: Speed reference from the source identified by
[Frequency mode sel] (FMOd) or the source identified by
[Remote spd ref 2] (F207) ≠ VIA signal
ON: Speed reference from the source identified by FMOd or the source
identified by F207 = VIA signal
53 [Inv. speed ref = VIA] Inversion of
Speed ref = VIA function
OFF: Speed reference from the source identified by
[Frequency mode sel] (FMOd) or the source identified by
[Remote spd ref 2] (F207) = VIA signal
ON: Speed reference from the source identified by FMOd or the source
identified by F207 ≠ VIA signal
Function No. / Description Action
- Altivar 212 1
- 2 S1A53838 09/2011 2
- Table of Contents 3
- 4 S1A53838 09/2011 4
- S1A53838 09/2011 5 5
- 6 S1A53838 09/2011 6
- Safety Information 7
- S1A53838 09/2011 9 9
- About the Book 10
- 10 S1A53838 09/2011 10
- General Overview 11
- 12 S1A53838 09/2011 12
- PROGRAMMING 14
- INSTALLATION 14
- Overview 15
- 16 S1A53838 09/2011 16
- Preliminary recommendations 17
- Embedded display terminal 18
- S1A53838 09/2011 19 19
- Monitoring Mode 20
- Run Mode 23
- Programming Mode 23
- Menu Navigation 24
- Programming 25
- [Quick menu] 25
- 26 S1A53838 09/2011 26
- F--- [EXTENDED MENU] submenu 27
- IO [I/O MENU] submenu 28
- Submenus 30
- Graphic display option 31
- • Press (ENT): 31
- • Turn +/-: 31
- Detected fault screens 33
- Pre-alarms screens 34
- Modbus communication status 34
- PCSoft software workshop 35
- Run forward 38
- Run reverse 38
- RUN STOP 39
- 2.2 to 10 kOhms 40
- 1/4 Watt 40
- 4-20 mAcurrent signal 41
- Feedback 44
- Feedback mA or voltage signal 44
- Setpoint 0 - 10 V 44
- Drive Operation 45
- S1A53838 09/2011 47 47
- 48 S1A53838 09/2011 48
- (F735) 51
- 52 S1A53838 09/2011 52
- 54 S1A53838 09/2011 54
- Quick Menu 55
- AU1 [Auto ramp] 56
- [Acceleration time 1] 56
- LL [Low limit frequency] 56
- UL [Upper limit freq] 56
- Pt [Mot cont. mode sel.] 57
- F417 [Motor rated speed] 59
- F601 [Motor Current Limit] 59
- 60 S1A53838 09/2011 60
- Programming Parameters 61
- Parameter Reset 62
- AU4 [Auto set function] 63
- F700 [Parameter lock] 64
- F738 [Quick menu AUF] 64
- Motor Control Parameters 65
- Motor Control Mode 66
- [Mot cont. mode sel.] (Pt) 68
- Motor Tuning 70
- F400 [Auto-tuning drive] 71
- Expert parameters 72
- F307 [Mot volt limitation] 73
- Motor 2 Control Parameters 74
- F418 [Frequency loop gain] 75
- F419 [Freq. loop stability] 75
- 76 S1A53838 09/2011 76
- Drive Control Parameters 77
- F721 [Loc. mot stop mode] 78
- F295 [Switch rem/Local] 78
- F256 [Time limit low spd] 78
- F207 [Remote spd ref 2] 78
- F650 [Forced fire control] 79
- F659 [Forced fire function] 79
- F294 [Forced speed freq.] 79
- F730 [Up/down key ref] 80
- F732 [Loc/rem key] 80
- F733 [Run/stop key] 80
- F734 [Priority stop] 80
- F735 [HMI reset button] 80
- Application Parameters 81
- Application parameters 82
- (1) (2) (3) (4) 83
- Skip Frequencies 87
- F250 [DC brake start freq.] 88
- F251 [DC braking current] 88
- F252 [DC braking time] 88
- F111 [LI F selection] 90
- F112 [LI R selection] 90
- F113 [LI RES selection] 90
- F109 [VIA selection] 90
- F118 [VIA LI selection] 90
- Inversion of commanded speed 98
- ≠ VIB signal 103
- Analog Input Functions 104
- Analog Output Functions 105
- Analog Input Adjustments 106
- F472 [VIB bias] 107
- F473 [VIB gain] 107
- F470 [VIA bias] 107
- F471 [VIA gain] 107
- F200 [Auto/man speed ref] 108
- [AO funct. selection] 108
- FM [AO scaling] 108
- F147 [FL Relay delay] 110
- F360 [PID control enable] 110
- F362 [PID Prop Gain] 110
- F363 [PID Integral Gain] 110
- Active Logic Function 112
- Preset Speeds 112
- Ω 3000 Ω 112
- +/- Speed Control Parameters 113
- F100 [Freq. 1 reached] 114
- F101 [Freq. 2 reached] 114
- F102 [Freq.2 bandw.] 114
- F167 [Freq band det range] 115
- F603 [Ext. fault stop Mode] 115
- F604 [DC brk time ext flt] 115
- Damper control 116
- F580 [Damper fdb type] 117
- F581 [Time open Damper] 117
- F582 [Time close Damper] 117
- F583 [Damper flt behavior] 117
- I/O Control Parameters 118
- 118 S1A53838 09/2011 118
- Display Parameters 119
- F710 [Displayed param.] 120
- F701 [Unit value selection] 120
- F708 [Display ref. resol.] 120
- F621 [Run time alarm] 120
- F748 [Power cons. memo] 120
- 122 S1A53838 09/2011 122
- What's in this Chapter? 123
- F303 [Number auto reset] 124
- Time delay 125
- F301 [Catch on fly] 126
- F632 [Mot overload memo] 126
- F602 [Drive fault memory] 127
- F608 [Input phase loss] 127
- F302 [Supply loss behav.] 127
- F627 [Undervolt detect.] 127
- F305 [Overvoltage fault] 128
- F626 [Overvoltage level] 128
- F605 [Output phase loss] 129
- F610 [Underload det.] 130
- F611 [Underload level] 130
- F609 [Underload band] 130
- F612 [Underload det. time] 130
- F633 [Loss of VIA] 130
- 0.0 to [Max frequency] (FH) 131
- F615 [Overtorque det.] 132
- F616 [Overtorque level] 132
- F618 [OvTorque det time] 132
- F619 [Overtorque band] 132
- F634 [Amb. temp. alarm] 133
- F481 [In noise comp. filter] 133
- F483 [In noise inhibit gain] 133
- F484 [Pwr supply adj. gain] 133
- Output Frequency (Hz) 134
- - and the protection 135
- 136 S1A53838 09/2011 136
- F800 [Mdb RJ45 baud] 138
- F801 [Mdb RJ45 parity] 138
- F802 [Modbus address] 138
- F856 [Mot. poles (comm.)] 140
- F870 [Block write data 1] 140
- F871 [Block write data 2] 140
- F875 [Block read data 1] 140
- F876 [Block read data 2] 140
- F877 [Block read data 3] 141
- F878 [Block read data 4] 141
- F879 [Block read data 5] 141
- F880 [Free ID parameter] 141
- Speed Reference 144
- Droop Control 145
- Output frequency (Hz) 146
- Command frequency: f 146
- Power running 146
- Torque current (%) 146
- Operation frequency: f 146
- What's in this Part? 147
- 148 S1A53838 09/2011 148
- Detected fault conditions 150
- Alarm Conditions 153
- Pre-alarm Conditions 154
- Clearing the detected fault 155
- 156 S1A53838 09/2011 156
- 158 S1A53838 09/2011 158
- Migration 159
- Migration ATV21 - ATV212 160
- Parameters Reset Tables 161
- 162 S1A53838 09/2011 162
- S1A53838 09/2011 163 163
- 164 S1A53838 09/2011 164
- [Display ref. resol.] 164
- S1A53838 09/2011 165 165
- (1) See table page 167 165
- 170 S1A53838 09/2011 170
- User Settings Tables 171
Related products and manuals for Remote starters Code Alarm F60
Remote starters Code Alarm F60 User's Guide
(107 pages)
(107 pages)
(8 pages)
Remote starters Code Alarm F65 User Manual
(19 pages)
(19 pages)
© 2020, manymanuals.com. All rights reserved. | 0.700 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals